Sargent and Greenleaf 6120 Operations Instructions download pdf (Page 18)

Operating Instructions

Model 6123—Motorized Electronic Combination Lock

duAl control mode

This is also referred to as dual user mode. It requires two different

valid lock codes to be entered within one minute of each other for

the lock to open. The idea is that no one person has the ability to

open the safe alone. Lock features can include time delay and time

delay override code, if desired. The holder of the master code can

perform all programming functions. The holder of the supervisor

code cannot perform any programming or code changes. He cannot

even change or delete his own code. User code holders can change

their own codes. You should also be aware that a single user time

delay override code can open the lock immediately without entry

of a second code. The dual control time delay override will require

another code to start the time delay before it can be used to open the

safe. A time delay period of at least one minute must be programmed

into the lock for a time delay override code of either variety to work.

It cannot open a lock that is not using the time delay feature.

If your lock is in another mode and you want to change it to dual

control mode, follow this programming sequence:

3 2

(_____) #



1 #



1 #



supervisor/user mode

This is sometimes referred to as supervisor/subordinate mode. In

this mode, the master code and the supervisor code cannot open

the lock. Instead, they are used to enable and disable the lock for

opening by the user codes. When either the master code or the

supervisor code (if set) is entered, the lock will emit four short beeps

or two long beeps. If it gives the four short beeps, any user code

can subsequently be used to open the lock. The next time the master

code or supervisor code is entered, the lock will emit the two long

beeps. Now the user codes cannot open the lock. When the lock is

disabled and a user code is entered, it does not open, but emits

two long beeps instead. The master code and supervisor code are

effectively used to toggle the lock back and forth between usable

and non-usable states. Lock features can include time delay, but the

time delay override is not available in this mode. The holder of the

master code can perform all programming functions. The holder of

the supervisor code (if it’s set) can set, change, and delete user

codes. He can also change and delete his own code. User code

holders can change their own codes and open the lock when it is

enabled by the master code or supervisor code.

To place your 6123 lock in supervisor/user mode, press:

3 2

(_____) #



2 #



2 #



setting / chAnging / deleting codes

the mAster code

As mentioned previously, the master code can perform all

programming functions for the 6123 lock. The master code can

be changed, but the lock will not allow you to delete it. The factory

default master code is 1 2 3 4 5 6 #. We strongly suggest you

change it to a six-digit code of your own choosing before storing

anything of value in your safe. Only the holder of the master code

can change the master code. The sequence is:

Press SG

(___) #



(___) #



(___) #



If the long error tone (brap) sounds at any time during the master

code changing procedure, you have made an error. The old master

code is retained.

the supervisor code

The supervisor code can change and delete itself (once set). It can

be set, changed, and deleted by the holder of the master code. The

process for using the master code to set or change the supervisor

code is:

Press SG

(___) #



(___) #



(___) #



If the long error tone (brap) sounds at any time during the supervisor

code changing procedure, you have made an error. The old

supervisor code is retained.

To delete the supervisor code, the master code holder enters:

Press SG

(___) #





existing master code

existing master code new master code new master code(7 4)

existing master code new supervisor code new supervisor code(7 4)

existing master code(7 4)

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 39 40

Comments to this Manuals

No comments

Sargent and Greenleaf 6120 Operations Instructions Page 18

Comments to this Manuals

Related products and manuals for Numeric keypads Sargent and Greenleaf 6120